Skip to content

Posts from the ‘Data Collection & Analysis’ Category

Feb 7

Soil sensors help solve putting green water distribution issues

Distribution of soil water in high-sand-content putting greens is a major concern for golf course superintendents. Gravel is commonly used as a component of a sand-based root zone to increase moisture retention, but due to gravity, the contour and slope of a putting green significantly affect moisture retention. Coarse-textured soils often become too dry in higher elevations and too wet in lower elevations. This hampers performance and increases water and labor inputs. 

Image of a golfer putting on a putting green at a golf course
The contour of a putting green affects moisture retention


To fix this problem, Thomas Green, a graduate student at Michigan State University, and a team of researchers are assessing the impact of gravel layer particle size and slope on soil water content in a variable-depth, high-sand content root zone.  He says, “Due to lack of published research and the USGA’s wide-ranged specification for gravel selection based on the root zone material, determining the optimal bridging, filtering, permeability, and uniformity factors capable of increasing root zone soil moisture uniformity is critical.”

Validating previous turfgrass experiments

Green and his team set out to validate previous turf experiments done at MSU which showed that increasing the particle size difference between the gravel and root zone (sand) layers, in combination with a variable-depth root zone (shallower at the slope apex, deeper at the slope base) would improve soil moisture uniformity. 

He says, “We wanted to retain this moisture consistently throughout the whole profile over the entire green. Our experiments decreased the root zone depth in relation to our gravel layer. So at the peak, we reduced the root zone, and in the valleys, we increased the root zone to eliminate wet spots where water accumulates.”

Water potential is the key

Green says the goal was to manipulate the “head” (or water potential) in the peaks and valleys. He explains, “We tested particle size differences between a high-sand, root-zone mix and the gravel layer. Past studies show that the greater the difference between the root zone particle size and the gravel particle size, the more water is retained at the interface. Essentially in the valleys, we increased the depth of the sand layer to create (in physics terms) a large head that forced more water to drain. At the top of the green, we did the opposite and made a thin layer of sand so more water was available. Basically, it was all about manipulating the water potential or tension on the water to retain the right level of moisture.”

The diagrams below illustrate the physics of how this works:

Diagram of sand and gravel layers in a putting green
Figure 1. Diagram of sand and gravel layers in a putting green

In Figure 1, the gravel provides a textural barrier where pores must be saturated for water to move into the gravel.

Close up diagram of tall sand layers in the valley
Figure 2. Closeup of tall sand layer in the valley

Figure 2 is a closeup of the tall layer. Cohesion of water molecules together and adhesion to soil particles ties water together and exerts downward force or tension on water at the top of the profile. The larger the height from the top of the profile to the saturated surface, the more tension on the water (lower water potential).

Close up diagram of short sand layer at the peak
Figure 3. Closeup of short sand layer at the peak

Figure 3 is a closeup of the short sand layer. Shorter height above the saturation zone reduces the tension in the top layer of soil (higher water potential). Thus, the high part of the green with the thinnest sand layer will have less tension and more water than the thick layer in the lower part of the green. To visualize what soil tension is like, think of people hanging on people (Figure 4). The more people there are, the more “pull” will be exerted on the top person.

Diagram of a comparison of soil tension to people hanging on people
Figure 4. Soil tension is like people hanging on people. The more people, the more pull exerted on the top person.

Eliminating edge effects

Green used METER soil moisture and temperature sensors at three different depths along with METER data loggers to validate that the water was in the right place. He inserted the sensors into an enormous box that mimicked a putting green. “I created a 4-ft x 4-ft module to simulate a sloping green. I had to figure out how large it should be to eliminate edge effects (water preferentially moving toward the container edges). The soil moisture sensor helped me determine just how large this box had to be to get accurate measurements.”

Green says the surface measurements were the most important, “I was interested in that top depth because in a golf setting, that’s where you need to control moisture. In a putting green, turfgrass roots aren’t very deep because the grass is so short.”

USGA has adopted the new method

Green says the results turned out as expected. “We expected that if we increased the gravel particle size difference and reduced sand depth, we would see increased water retention in our root zone profile, and that’s exactly what happened. The great thing is the USGA has now somewhat adopted these new recommendations. More and more golf courses are going to this construction method. It’s good for the industry because they’re conserving water.”

In the future, Green says he’d like to explore some research done by F.W. Taylor in the early 1900s. Taylor thought about using a vertical sand or gravel strip contoured on a slope to form a barrier to water moving downhill instead of plastic or polyethylene. This idea is illustrated beautifully in the classic 1950s era film by Dr. Walter Gardner.

Download the researcher’s complete guide to soil moisture—>

Download the researcher’s complete guide to water potential—>

LinkedInMessengerRedditThreadsCopy

Jan 8

Best of 2019: Environmental Biophysics

In case you missed them, here are our most popular educational webinars of 2019. Watch any or all of them at your convenience.

Lab vs. In Situ Water Characteristic Curves

Image of a researcher running hand across wheat

Researcher Running A Hand Across Wheat

Lab-produced soil water retention curves can be paired with information from in situ moisture release curves for deeper insight into real-world variability.

Watch it here—>

Hydrology 101: The Science Behind the SATURO Infiltrometer

Image of a fallen tree being supported off the ground by many other trees

A Forest With Fallen Trees

Dr. Gaylon S. Campbell teaches the basics of hydraulic conductivity and the science behind the SATURO automated dual head infiltrometer.

Watch it here—>

Publish More. Work Less. Introducing ZENTRA Cloud

Image of a researcher collecting information from a ZL6 data logger

Researcher is Collecting Data from the ZL6 Data Logger

METER research scientist Dr. Colin Campbell discusses how ZENTRA Cloud data management software simplifies the research process and why researchers can’t afford to live without it.

Watch it here—>

Soil Moisture 101: Need-to-Know Basics

Soil moisture is more than just knowing the amount of water in soil. Learn basic principles you need to know before deciding how to measure it.

Watch it here—>

Soil Moisture 201: Moisture Release Curves—Revealed

Image of rolling hills of farm land

Rolling Hills of Farm Land

A soil moisture release curve is a powerful tool used to predict plant water uptake, deep drainage, runoff, and more.

Watch it here—>

Soil Moisture 301: Hydraulic Conductivity—Why You Need It. How to Measure it.

Image of a researcher measuring with the HYPROP balance

Researcher measuring with the HYPROP balance

If you want to predict how water will move within your soil system, you need to understand hydraulic conductivity because it governs water flow.

Watch it here—>

Soil Moisture 102: Water Content Methods—Demystified

Image of a researcher holding a TEROS 12 in front of a field

Modern Sensing is more than just a Sensor

Dr. Colin Campbell compares measurement theory, the pros and cons of each method, and why modern sensing is about more than just the sensor.

Watch it here—>

Soil Moisture 202: Choosing the Right Water Potential Sensor

Image of a dirt plowed field being used for electrical conductivity

Electrical Conductivity

METER research scientist Leo Rivera discusses how to choose the right field water potential sensor for your application.

Watch it here—>

Water Management: Plant-Water Relations and Atmospheric Demand

Dr. Gaylon Campbell shares his newest insights and explores options for water management beyond soil moisture. Learn the why and how of scheduling irrigation using plant or atmospheric measurements. Understand canopy temperature and its role in detecting water stress in crops. Plus, discover when plant water information is necessary and which measurement(s) to use.

Watch it here—>

How to Improve Irrigation Scheduling Using Soil Moisture

Image of a crop field

Capacitance

Dr. Gaylon Campbell covers the different methods irrigators can use to schedule irrigation and the pros and cons of each.

Watch it here—>

Next up:

Soil Moisture 302: Hydraulic Conductivity—Which Instrument is Right for You?

Image of plants growing out of the sand

Leo Rivera, research scientist at METER teaches which situations require saturated or unsaturated hydraulic conductivity and the pros and cons of common methods.

Watch it here—>

Image of grapes growing off of a tree

Predictable Yields using Remote and Field Monitoring

New data sources offer tools for growers to optimize production in the field. But the task of implementing them is often difficult. Learn how data from soil and space can work together to make the job of irrigation scheduling easier.

Watch it here—>

Learn more

Download “The researcher’s complete guide to soil moisture”

Download “The researcher’s complete guide to water potential”

LinkedInMessengerRedditThreadsCopy

Nov 4

The effects of environmental change on carbon cycling across the semi-arid west

Meet Christopher Beltz: G.A. Harris Fellowship winner

Increased nitrogen availability has the potential to alter many ecosystem functions—and is doing so already. This is due to the widespread response of net primary productivity (biomass) and soil respiration to increased nitrogen inputs into the biosphere.

Image of the grass lands with the sun setting

Grass Lands

Increases in nitrogen inputs are responsible for the acidification of soils, streams, and lakes and can affect forest and grassland productivity. Former G.A. Harris Fellowship winner, Christopher Beltz, a PhD student at Yale University, and his research team are examining two major drivers of carbon cycling: water and nitrogen. They want to understand the degree of limitation by both of these factors in the semi-arid ecosystems of the western United States and if that limitation changes by specific function.

Inspired by a mitigation pilot project

Beltz decided to study the effects of increased nitrogen on biomass after learning about the initiation of a major energy development in a sagebrush steppe system which caused declines in a local mule deer herd. He says, “One hypothesis was that the development significantly reduced available winter range forage and also impacted the use of it as the animals moved more quickly through the noisy environment. They wanted to see if the widespread application of fertilizers would potentially offset the loss of biomass and increase the forage quality. In the end, it was clear that the effect of nitrogen fertilization alone would have minimal to no effect. However we also noticed some variability in the results and that this variability seemed to be related to precipitation.”

Image of a scientist watering a field plot

Scientist Watering Field Plot

Beltz thought that if he could control the water in a system in addition to nitrogen, the results might be more consistent. Thus, Beltz and his research team broadcast nitrogen over the soil at three semi-arid grassland and shrubland/sagebrush sites in Colorado and Wyoming. He says, “The three sites essentially have a similar species list, annual precipitation, and annual temperature. However, temperature increases as you go south, and there are some differences in seasonality. The shrublands in the far north are the driest in the late summer which is typical of shrublands, where you see a large amount of precipitation occurring in the spring with a deficit in the summer. Larger taproots are beneficial in this system because they can access deeper water reservoirs.”

Measuring soil moisture improves understanding

The team used METER all-in-one weather stations, soil moisture sensors, and data loggers to monitor site conditions (i.e., precipitation, air temperature, soil moisture, and soil temperature) with high temporal resolution. Beltz explains, “We monitored soil moisture to understand whether our treatments were having any effect. We needed to know if the treatments actually altered the soil water conditions. With soil sensors in the ground, we could monitor that. We also monitored precipitation at the site level because of the fine scale spatial heterogeneity of precipitation in these systems. We weren’t confident we could obtain this with interpolation or modeling; we wanted site-specific values.”

Beltz uses this and other data to understand the interactive effects of nitrogen and water and also changes in water and nitrogen concentrations. He says, “We do a classic full-factorial manipulation outdoors. We perform the exact same manipulations with the same timing at each site. We measure a whole suite of variables that range from ecosystem structure to ecosystem function. This includes soil respiration, plant community, soil microbial communities (fungal and bacterial) using next-generation sequencing. We look at pools of soil carbon, and we do some fractionation so we can get at more labile and recalcitrant carbon compounds.”

METER weather station, ZL6 data logger, and soil moisture sensors

METER Weather Station, ZL6 Data Logger, and Soil Moisture Sensors to Receive and Process Data

Beltz says that monitoring soil moisture at multiple depths is important. “Our soil samples come from the same depths as the sensors so we can differentiate depth when we look at changes in bacterial or fungal composition. We then try to tie that to temperature and moisture. In 2018, we added an additional set of soil moisture sensors in our water treatment so we could start to quantify the effect in the soil depth that those water treatments were having. This helped explain a lot of what we were seeing.”

Nitrogen or water: which is the driver?

Beltz says the analyses are ongoing, but what they’ve learned so far is that an application of water equivalent to 12 millimeters precipitation penetrates to 10 centimeters of depth, and the effect of that application lasts three to seven days at all of their sites. He says, “Last year, we had an unseasonably large amount of precipitation at our northerly site. So for most of the season, the water treatments and the controls were identical in terms of water availability. That was a very helpful context for us because we started to see things that did not match the expected patterns.”

Looking at the big picture, he adds, “What’s come out of this is not what anybody expected. One major finding, at least in the initial analyses at two of our sites, is that it’s really the combined treatment of increased nitrogen and water that has the effect. This is not necessarily surprising in some ways, however it is the widespread lack of response of any other treatment combination that is extremely interesting.”

What it all means

Beltz sums up the implications of his research like this: “We know water availability and precipitation will shift globally due to climate change, as well as nitrogen deposition and availability. Our research is trying to tease apart the effects of two factors, at least within the western United States, that we know are likely to cause changes to the structure and function of dryland ecosystems. As we start to look at carbon balance or shifts in function or species competition of plant communities, we are finding out that it’s the combined effect of increased nitrogen and water that will cause a more major change as opposed to just one or the other. It’s important that we integrate that combination into models that often do not account for both of these factors.”

Beltz says in the future he’s interested in continuing his work in the carbon/nitrogen cycle world, and he wants to look at integrating nitrogen and water into carbon balance modeling efforts.

You can read more about the first study mentioned, regarding nitrogen fertilization in the sagebrush steppe, which was published in PloS ONE: https://doi.org/10.1371/journal.pone.0206563

Find out about his research here: christopherbeltz.com or via Twitter @BeltzEcology

Now accepting applications: 2019 G. A. Harris Fellowship

The Grant A. Harris Fellowship provides $60,000 worth of METER research instrumentation (six $10,000 awards) to graduate students studying any aspect of agricultural, environmental, or geotechnical science.

Apply now

Learn more

See ATMOS 41 weather station performance data

Learn more about measuring soil moisture. Download “The researcher’s complete guide to soil moisture“.

To understand how soil moisture and soil water potential work together, download “The researcher’s complete guide to water potential.”

LinkedInMessengerRedditThreadsCopy

Oct 16

Data deep dive: why am I seeing diurnal changes in soil moisture?

In the video below, METER soil scientist Dr. Colin Campbell discusses an often-misdiagnosed water content signal that looks like typical diurnal temperature cycling but is actually due to a phenomenon called hydraulic redistribution. He shows how easily these patterns can be seen in ZENTRA Cloud data management software.

Watch the video

 

 

 

Learn more

Learn more about measuring soil moisture. Download “The researcher’s complete guide to soil moisture“.

To understand how soil moisture and soil water potential work together, download “The researcher’s complete guide to water potential.”

Video transcript

Hello, my name is Colin Campbell. I’m a research scientist here at METER Group. And today we’re going to be digging into some water content data that I collected over the last summer. This is a field that’s planted in spring wheat, it’s about 700 meters across. And we’ve set up six measurement sites. At each one of these sites, we’re making several measurements, but the ones we’re going to talk about today are just water content. And while we’ve installed water content sensors at 15, 45, and 65 centimeters, we’re just going to focus on the 65-centimeter water content sensors. These sensors are the METER TEROS 12 soil moisture sensors, so they also measure electrical conductivity and temperature, and we’re going to look at temperature as well because that figures into this discussion. 

So this field was planted in April of 2019. And not a lot interesting goes on at the 65-centimeter depth through April, May, and June. But as we get into July, the wheat is reaching maturity, and they essentially are going to cut off the irrigation water here on July 22. So up to July 22, there’s really not a lot of movement in the water content. One of the sites decreases a little bit, but each line is flat. What I noticed as I was looking at this particular graph is after this long period of very flat data, after June 22 when the irrigation was cut off, we start to see some movement in the water content at this depth Not only is there movement down, but there’s a daily movement of the actual water content signals, all but this top light green line. And it made me wonder, what’s going on? 

Image of a field of wheat

Diurnal water content fluctuations are not always due to temperature.

Initially, whenever you see a diurnal movement, you suspect that it’s caused by temperature. It’s been said that every sensor is probably a temperature sensor first, and a sensor of whatever we’re really interested in second. In this case, we can look to see what the temperature is doing at that depth. Here’s soil temperature, at 65 centimeters, and even though there’s just a little bobble in the line, the line is almost completely flat. We see the seasonal trends in temperature, but really no diurnal temperature cycling. And this scale is also fairly small. So back to our 65-centimeter water content. If it’s not temperature that’s affecting these lines, then what is it? 

I’ve seen this before in an experiment that I did years ago in a non-irrigated wheat field. We were measuring down at  150 centimeters, and when the water had been used up in the upper levels of the soil profile, the roots of the wheat plant just simply went down to 150 centimeters and started taking water up. So this is what I assume is also happening here. The wheat has extended its roots down to 65 centimeters, since its irrigated wheat. That’s not too deep, but wheat doesn’t necessarily need to get its roots down super deep. And as the wheat accesses that water, we’re seeing these daily drops in water. But then we’re seeing just a slight increase in water. Here on July 28, we’re seeing that water go up slightly. And so why is this happening? We might understand how the water is being taken out of the soil, but why do we see a slight increase in the water content (just a few tenths of a percent)? 

What I think is happening, in this case, is that it’s not temperature, but actually, roots are growing down into this area, and they’re probably growing around the sensor. As we change from day to night, we see a release in the elasticity of the water in the xylem, and maybe just a little bit more water down in the roots as they’re the transpiration pull of the day is lessened and stops overnight. The stomates are closed, and we see just a little bit of water coming back into the roots and possibly into the soil. 

Now there was a big discussion many years ago about whether this was something called hydraulic lift where trees could take up water from deep in the soil profile and essentially give it back to plants near the surface. And although it was a great debate, it was never proven that this actually happened: water being spread from deeper locations to more shallow locations by roots. But this is probably hydraulic redistribution where we just have roots filling with water, and when they are filled, we see a little bit in the water content sensor.

LinkedInMessengerRedditThreadsCopy

Oct 3

Soil moisture sensors aid forensic science in time-of-death estimates

Extending time of death estimates

Forensic scientists are looking at better, more accurate ways of determining the post-mortem interval, or time of death. When a human body decomposes, microbes and nematodes become abundant in the soil surrounding the body. The types and maturity of these organisms may be a means of determining the time of death, but thus far most studies have focused on short post-mortem time frames.

Image of a footprint in the dirt
Scientists look for ways to increase the accuracy of long-term post-mortem interval estimates

That’s why Stacy Taylor, her advisor, Dr. Jennifer DeBruyn, and their research team at the University of Tennessee are using cutting-edge molecular techniques and classical microscopic techniques to try and extend the time frames over which this approach could be used to determine how long it’s been since victims have died. 

Monitoring dramatic soil changes   

Taylor, a winner of the National Institute of Justice Graduate Research Fellowship in STEM, working in conjunction with the UT Anthropology Research Facility, is measuring biological and chemical changes in soil composition brought about by long-term human decomposition. She says, “We are looking at a combination of soil chemistry, microbial ecology, and some of the soil animals, particularly the nematodes, to get an entire food web approach in understanding all of the nutrient cycling that is occurring in these systems. We want to look at the soil chemistry patterns and microbial/nematode succession to see if these cross-inform each other.” 

Taylor explains some of the changes in soil composition that occur during both vertebrate and invertebrate decomposition, “Basically, any time you have a decomposition event that is not composed of plant litter, it creates what’s called a “hot spot” of nutrient enrichment. Unlike plant litter, which decomposes very slowly, with a vertebrate system you have a tremendous amount of protein and fat. You also have a lot of calcium, magnesium, sodium, and potassium. And when you put a large load of these things into the soil, you get a huge change in soil organic composition, nutrient availability, and soil moisture. So you’re essentially dealing with massive changes in a very localized soil environment.”

Decomposition also changes the soil water

Taylor and her adviser Dr. Debruyn had the fairly new idea to insert METER soil moisture, temperature and electrical conductivity sensors connected to data loggers into the soil in these hot spots, to see what kind of interesting data would turn up.

Updated version of the TEROS 12 sensor
The TEROS 12 is an updated version of the sensor Taylor used in her research

She says they’ve been surprised at how informative and eye-opening this has been. She explains, “These hot spots change the ionic strength of the soil water. And that is highly correlated to electrical conductivity, which is measured by the soil moisture sensors. A change in ionic strength potentially impacts the salinity of the soil. Some of those changes have been shown to persist for well over a year, which is what these soil sensors are showing. I take an hourly reading, and the sensors are producing the most amazing data.”  

Taylor says the sensors were inserted into the soil surface, so they could measure the impact the decomposition produced immediately on the upper layer of soil. They took soil cores at 16 centimeters to measure soil pH and EC, and they also used RT-1 air temperature sensors to track accumulated degree days which are based on ambient air temperature and correlate with maggot growth and development rates. 

Identifying time markers

Taylor says that soil changes (in particular EC and temperature) are not just general deviations but show clear stages as decomposition progresses through time, indicating they might be useful as time markers. She explains, “We are tracking a succession of events. These events happen at particular time points and are associated with certain decomposition stages (i.e, bloat, active decay, advanced decay, or skeletonized remains). For example, you might see traces of increased electrical conductivity followed by a drop. If that drop happens at the same stage of decomposition, over and over, then you know that you have a time marker. And when you gradually accumulate some of these time markers, that can potentially inform some of the existing estimates of how long something has been there.”

Crime scene tape in front of an accident
Taylor’s study is about bringing better justice and more peace to the families of crime victims.

What’s the future?

Taylor says the implications of this study will help nail down many of the intrinsic controls on the decomposition process. And once they understand that, they’ll have a better idea how to employ these estimates of post mortem interval, which will bring better justice and more peace to the families of crime victims. About the future of the research, she says, “This is the kind of study that you want to replicate at other human decomposition facilities that vary by altitudes, weather, soils, and more. You need to be able to look at a variety of environments just to see what happens.”

You can read more about Stacy’s project here.

To learn more about measuring soil moisture, download “The researcher’s complete guide to soil moisture“.

To understand how soil moisture and soil water potential work together, download “The researcher’s complete guide to water potential.”

LinkedInMessengerRedditThreadsCopy

Jul 12

Freshwater shrimp grown in Korean rice paddy boost grower income

In South Korea, falling rice prices threaten the livelihood of many rice growers. Recently our Korean reps told us about an experiment performed in Jinju city, Gyeongsangnam-do, South Korea, by GNARES (Gyeongsangnam-do Agricultural Research & Extension Services) to increase grower income through simultaneous freshwater shrimp, lotus plant, and rice cultivation in a paddy field.

Image of a researcher working on freshwater shrimp growth

RT-1 water temperature sensors were installed along with METER data loggers to monitor the water temperature, ensuring it was optimal for shrimp growth. Through this experiment, GNARES found that environmental conditions were good for cultivating freshwater shrimp in this area. 

Graphs show the plantations are good for cultivating freshwater shrimp

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get METER news
LinkedInMessengerRedditThreadsCopy

Jun 12

Engineers Without Borders alleviates Panamanian village water security issues

Engineers Without Borders (EWB) at Washington State University in Pullman, WA has partnered with a small indigenous village located in the Comarca Ngäbe-Buglé region of Panama. The relationship between this village and EWB at WSU began in 2016 when WSU alumna Destry Seiler began living in the village as a Peace Corps volunteer hoping to help solve the community’s water security needs.

A picture of Comarca Ngäbe-Buglé region photo taken from a small village in Panama

A view of the Comarca Ngäbe-Buglé taken from the village in Panama.

During the rainy season in this village, approximately 20 households have access to water through a two-inch PVC pipe that operates by gravity. It runs approximately 1.5 kilometers through the jungle from a spring source higher in the mountain to small hose spickets located close to the homes on the distribution line. The other ~80 households do not have access to the distribution line and walk to the closest river or creek up to five times a day to find water. However, during the dry season, most spring sources dry up, leaving all households in the community to walk to the diminished supply of rivers to find their water.

Water line supplying 20 village homes with water during the rainy season

A view of the water line currently serving ~20 homes in the village during the rainy season.

The village initially requested assistance from the Peace Corps in order to find a year-round source of clean water. But, after living in the village for 1.5 years, Ms. Seiler could not locate spring sources that both survived through the dry season and could also reach the homes in need through a gravity fed system.

Then Ms. Seiler began thinking of groundwater as a possible new water source for the community. Unfortunately, groundwater data for the Comarca Ngäbe-Buglé was not available from the local government agency. So she decided to reach out to WSU professor, Dr. Karl Olsen, to ask for assistance with a groundwater research project, and the EWB club was formed.

The club visited the village for the first time along with Ms. Seiler and faculty mentor Dr. Karl Olsen in August 2018 to do an initial survey of water use and needs, as well as to create a first-ever map of the area. EWB will return to Panama this June 2019 to implement a solar-powered water pump requested by a section of the community to deliver water from a spring source to approximately 20 homes on the nearest ridgeline. The club will also install latrines in a nearby community. They will continue the groundwater survey of the area through more extensive mapping and perform a more advanced analysis with the support of a local hydrologic company.

EWB members and WSU students next to the village sign

EWB members and WSU students Patrick Roubicaud, Kristy Watson, Destry Seiler, Perri Piller, Rene McMinn, and Kevin Allen during their visit to Panama, August 2018.

The team will use a METER-donated ATMOS 41 weather station along with a ZL6 data logger and ZENTRA Cloud software to assist in the data collection necessary to begin mapping groundwater in the area. The weather station will record precipitation, solar radiation, vapor pressure, temperature, wind, and relative humidity data that will enable EWB to begin to quantify environmental conditions and available water supply. When combined with streamflow data from rivers in the area, groundwater availability can also begin to be estimated. Because of ZENTRA Cloud, EWB will be able to view this information near-real time as well as share it with the village to help guide their design decisions. EWB plans to install the ATMOS 41 at a nearby village school to ensure weather station security and to provide an opportunity for local students to learn about their surrounding environment in a way they have not been able to do before.

To learn more about the Panamanian village or the work EWB from WSU is doing, visit ewb.wsu.edu.

See weather sensor performance data for the ATMOS 41 weather station.

Explore which weather station is right for you.

Download the “Researcher’s complete guide to soil moisture”—>

Download the “Researcher’s complete guide to water potential”—>

LinkedInMessengerRedditThreadsCopy

Apr 12

Why mesonets make weather prediction more accurate

The staggering cost of Montana’s “flash drought”

Some people figured it was climate change. One statistician said it was a part of a cyclical trend for poor crop years. Whatever the cause, the 2017 flash drought that parched the entire state of Montana and most of South Dakota, severely impacted the profitability of ranchers and farmers. In western Montana, fires burned some of the largest acreages in recent history. It resulted in one of the biggest wildfire incident reports (over one-million acres) and caused virtually 100% crop loss in northeastern Montana. The U.S. Dept. of Agriculture estimated the crop loss to be in the hundreds of millions of dollars, and one question was on everybody’s mind—why did no one see it coming?

Montana drought status chart

Figure 1. Montana drought conditions August 2017 (Source: Montana State Library website: https://mslservices.mt.gov/Geographic_Information/Maps/drought/)

Getting the right weather data

The 2017 Montana Dept. of Natural Resources and Conservation spring drought report indicated plenty of water: “By the end of the month, almost all drought concern was removed from the state, with the exception of Wibaux and Fallon Counties….As of May 9, 2017, Montana was 98.45% drought free.” But in late May, an abrupt shift in weather conditions led to one of the hottest, driest summers on record.

The problem, says Kevin Hyde, Montana State Mesonet Coordinator, lies not only in the need for more weather data but in obtaining the right kind of data. He says, “One of the reasons drought was missed was because we’re still thinking you measure drought by snowpack and how much water is in the river, which is really great if you’ve got water rights. But we’ve got a lot of dryland out there.”

In addition to weather monitoring, Hyde is a big proponent of adding soil moisture and NDVI measurements to each of the Montana Mesonet stations he oversees. He says, “The conventional weather station only measures atmospheric conditions. But ultimately, to make any decisions, we’ve got to know not just how much water comes into the system, but how much goes into the soil. And even that’s not enough…because what we really need to know is how the water situation is going to affect plants.”

Hyde says more data are needed to warn growers and ranchers about upcoming weather risks. He points to the fact that increasing evapotranspiration got missed leading up to the summer of 2017. “We realized that if we were looking carefully at reference ET, we might have seen it about a month earlier. What would people have done? They would have changed their calf purchases. They would have figured out what kind of forage they needed to buy. These are the types of decisions people can make if they know the information sooner.”

Was the drought over? Soil moisture illuminates the bigger picture

Heavy rains came mid-September of 2017, which led some people to believe the drought was over. However, changes in soil moisture told a different story. Very little of the rain made it into the soil. “At the Havre, MT station you can see we had some heavy precipitation events. Then we had early October snows. So people expected good soil water recharge. But at the end of the day, we didn’t get it. On Sept.15th, soil moisture sensors showed a big soil moisture response at the surface but only a marginal response at 8 inches.” The melt of early October snows onto the soil, still damp from the September rain, drained to 20 inches or more. But as the snowmelt dissipated, there was minimal net gain going into the winter.

Soil moisture chart for Montana

Figure 2. Soil moisture traces at the Havre, MT weather station

Predictive models need more coverage to be effective

Typically in the U.S., the National Weather Service (a division of NOAA) puts out a network of weather monitoring stations spaced out across the country, and that data gets fed into forward-looking models that help predict the weather. Dr. Doug Cobos, research scientist at METER says, “What people are finding out is that putting in a sparse network of very expensive systems has done really well. It’s been a good thing. But the spatial gaps in those networks are a problem, especially for agriculture producers and ranchers. They need to know what’s happening where they are.”

Hyde agrees, adding that we need better predictive tools that help growers and ranchers make practical decisions based on data rather than guessing. “January 1st is when the decision has to be made—do I buy cows? Do I sell cows? Do I need more pasture? But many predictions start on April 1st. As one rancher puts it, ‘We don’t bother with Las Vegas. We sit around the dining room table at the beginning of the year and put a million dollars on one shot.’”

Mesonets improve spatial distribution

Mesonets present a practical solution for the need to fill in data gaps between large, complex weather stations. The Montana Mesonet currently has 57 stations interspersed throughout the state, and through partnerships with both the public and private sector, they’re adding more stations every year.

Map of mesonet weather stations

Figure 3. Map of MT Mesonet weather stations (source: http://climate.umt.edu/mesonet/)

At each location, the Montana Mesonet team installs METER all-in-one weather stations, soil moisture sensors, NDVI sensors and data loggers that integrate with ZENTRA Cloud: an easy-to-use web software that seamlessly integrates into third-party applications through an API. He says the system enables better spatial distribution and reliability. “When we were deciding on equipment we asked ourselves: What kind of technology should we use? It had to provide high data integrity. It had to be easy to deploy and maintain. And it had to be cost effective. There’s not a lot of people in that sector. METER systems are low profile, they’re affordable, and the reliability is there. I look at some other mesonets, and they cannot afford to build out further because they are relying on large, complex, expensive systems. That’s where the METER system comes into play.”

Montana mesonet weather station setup

Figure 4. Montana Mesonet station setup (Photo credit: Kevin Hyde)

Betting on the future

The Mesonet team and its partners are excited to see how their data will mesh with the available predictive tools to be the most useful and practical for growers and ranchers throughout the state, and they realize that there is still much work to do. “It’s not enough just to get the instrumentation out there. The overall crux is: how do we build the information network, and how do we build a relationship with the producers so that we can have an iterative and interactive conversation?” says Hyde. “We know there needs to be an education in how to use and interpret the data. For example: what is NDVI, and what can we learn from it? A lot of what we need to do is translate science into practical terms.” But he adds that it doesn’t need to be perfect. “What the farmers have said to us is, ‘We don’t need exact numbers. We’re gamblers. Give us probability. Teach us what it means, and we’ll make the decision.’”

Find more information on the Montana Mesonet here and in their newsletter.

See weather sensor performance data for the ATMOS 41 weather station.

Explore which weather station is right for you.

Download the “Researcher’s complete guide to soil moisture”—>

LinkedInMessengerRedditThreadsCopy

Feb 19

Why does my soil moisture sensor read negative?

How is a negative number possible?

METER soil moisture sensors measure the dielectric constant of the substrate in which they are installed. They are designed to measure soil, which has a dielectric constant of around 5.

Researcher holding a TEROS 12 soil sensor in front of a wheat field

METERTEROS 12 soil moisture sensor

Water has a dielectric of approximately 80, so if we assume that a dry soil has a dielectric of 5 (VWC = 0.00 m3/m3), then changes to the bulk dielectric read by the soil moisture sensor will be attributable to changes in water content. If you read a METER sensor in air, which has a dielectric constant of 1, you will quite naturally get a negative number.   

Improving accuracy of dielectric soil moisture sensors

There are two common causes for negative readings on a METER soil moisture sensor:  

1) Poor contact with the soil resulting from improper installation or disturbance

Air gaps next to a sensor will contribute the lower dielectric of air to the measurement resulting in an underestimation of VWC. Air gaps can arise if enough care is not taken to pack soil around the sensor body to approximate native bulk density. Sensors that have been disturbed, such as having a cable tripped over, can also develop air gaps that can result in negative results in dry soils. (To reduce the possibility of air gaps when installing METER sensors, use the new TEROS borehole installation tool) 

2) A calibration that is inappropriate for the soil in which the sensor is installed

If the standard mineral calibration is used, an error of ~ 3-4% can be expected in METER sensor readings. Negative numbers can be observed in oven-dry soils (by definition a VWC of 0.0 m3/m3) down to ~ – 0.02 m3/m3 with no malfunction of the sensor. The dielectric constant of the soil is assumed to be 5 and this is a valid assumption in the majority of soils of primarily mineral composition. If your soil has a different dielectric constant, such as can occur in soils with high organic matter content, then the uncertainty in your measurements will increase. This is not a large problem because METER sensors can be calibrated to match a given soil with very little investment in resources.

Want more details?  

Watch our webinar titled Why Does My Sensor Read Negative below. This webinar is designed for those who use electromagnetic sensors (capacitance/TDR/FDR) to measure soil water content. Learn about the theory behind the measurements. Dr. Doug Cobos discusses:

  • What is volumetric water content?
  • Dielectric measurement theory basics
  • Dielectric mixing models
  • Why might a sensor read a negative VWC?
  • Can a sensor really have 2% VWC accuracy for all soils?
  • Sources of error in dielectric measurement methods
  • Improving accuracy of dielectric measurements

 

Take our Soil Moisture Master Class

Six short videos teach you everything you need to know about soil water content and soil water potential—and why you should measure them together.  Plus, master the basics of soil hydraulic conductivity.

Watch it now—>

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

LinkedInMessengerRedditThreadsCopy

Nov 7

How to get started with ZENTRA Cloud

Researchers need to optimize funding and maximize peer-reviewed paper output. ZENTRA Cloud’s powerful data management software works with the new ZL6 data logger to make it easier to succeed at both.

METER ZL6 Data Logger providing information to a researcher

ZENTRA Cloud reduces workload by speeding up analysis, streamlining workflow, and simplifying data sharing.

Try ZENTRA Cloud now

Want to explore how ZENTRA Cloud works? Request access to a live test account.

Take a ZENTRA Cloud guided tour

Get a comprehensive look at ZENTRA Cloud’s capabilities and learn how to get started here.

Download the “Researcher’s complete guide to soil moisture”—>

LinkedInMessengerRedditThreadsCopy
« Older Entries
Newer Entries »