Data deep dive: When to doubt your measurements
Dr. Colin Campbell discusses why it’s important to “logic-check” your data when the measurements don’t make sense.
Wasatch Plateau
In the video below, he looks at weather data collected on the Wasatch Plateau at 10,000 feet (3000 meters) in the middle of the state of Utah.
Video transcript
My name is Colin Campbell, I’m a research scientist here at METER group. Today we’re going to spend time doing a data deep dive. We’ll be looking at some data coming from my research site on the Wasatch Plateau at 10,000 feet (3000 meters) in the middle of the state of Utah.
Right now, I’m interested in looking at the weather up on the plateau. And as you see from these graphs, I’m looking at the wind speeds out in the middle of three different meadows that are a part of our experiment. At 10,000 feet right now, things are not that great. This is a picture I collected today. If you look very closely, there’s an ATMOS 41 all-in-one weather station. It includes a rain gauge. And down here is our ZENTRA ZL6 logger. It’s obviously been snowing and blowing pretty hard because we’ve got rime ice on this post going out several centimeters, probably 30 to 40 cm. This is a stick that tells us how deep the snow is up on top.
One of the things we run into when we analyze data is the credibility of the data and one day someone was really excited as they talked to me and said, “At my research site, the wind speed is over 30 meters per second.” Now, 30 meters per second is an extremely strong wind speed. If it were really blowing that hard there would be issues. For those of you who like English units, that’s over 60 miles an hour. So when you look at this data, you might get confused and think: Wow, the wind speed is really high up there. And from this picture, you also see the wind speed is very high.
But the instrument that’s making those measurements is the ATMOS 41. It’s a three-season weather station, so you can’t use it in snow. It’s essentially producing an error here at 30 meters per second. So I’ll have to chop out data like this anemometer data at the summit where the weather station is often encrusted with snow and ice. This is because when snow builds up on the sonic anemometer reflection device, sometimes it simply estimates the wrong wind speed. And that’s what you’re seeing here.
This is why it’s nice to have ZENTRA cloud. It consistently helps me see if there’s a problem with one of my sensors. In this case, it’s an issue with my wind speed sensors. One of the other things I love about ZENTRA Cloud is an update about what’s going on at my site. Clearly, battery use is important because if the batteries run low, I may need to make a site visit to replace them. However, one of the coolest things about the ZL6 data logger is that if the batteries run out, it’s not a problem because even though it stops sending data over the cellular network, it will keep saving data with the batteries it has left. It can keep going for several months.
I have a mix of data loggers up here, some old EM60G data loggers which have a different voltage range than these four ZL6 data loggers. Three of these ZL6s are located in tree islands. In all of the tree islands, we’ve collected enough snow so the systems are buried and we’re not getting much solar charging. The one at the summit collects the most snow, and since late December, there’s been a slow decline in battery use. It’s down. This is the actual voltage on the batteries. The battery percentage is around 75%. The data loggers in the two other islands are also losing battery but not as much. The snow is just about to the solar charger. There’s some charging during the day and then a decrease at night.
So I have the data right at my fingertips to figure out if I need to make a site visit. Are these data important enough to make sure the data loggers call in every day? If so, then I can decide whether to send someone in to change batteries or dig the weather stations out of the snow.
I also have the option to set up target ranges on this graph to alert me whether the battery voltage is below an acceptable level. If I turn these on, it will send me an email if there’s a problem. So these are a couple of things I love about ZENTRA cloud that help me experiment better. I thought I’d share them with you today. If you have questions you want to get in contact me with me, my email is [email protected]. Happy ZENTRA clouding.
Download the researcher’s complete guide to soil moisture—>
Download the researcher’s complete guide to water potential—>
