Skip to content

Posts tagged ‘soil moisture’

Oct 16

Measuring Frozen Water Potential: How and Why?

In China recently, a fellow scientist asked Dr. Colin Campbell if matric potential sensors work in frozen soils.  His answer? Sort of. In this blog, he explains what he meant by his enigmatic reply: When water freezes in the soil, most matric potential sensors won’t work accurately because frozen water essentially disappears to the measurement. For example, in a dielectric measurement circuit, most of the water that was polarized in the electromagnetic field solidifies in the ice matrix. Thus, because dielectric measurements determine the charge that is stored when water is polarized, ice is not measured. But, many matric potential sensors contain a component that will measure frozen water potential: the temperature sensor.

Frozen ground with horseshoe prints

Horseshoe prints in frozen soil.

How Does Temperature Measure Water Potential?  

The temperature of a frozen matrix like soil has a fundamental thermodynamic relationship to the energy state of that water. For every one degree C below freezing, the water potential decreases by 1.2 MPa. For example, if the soil drops down to -4 C, the soil water potential will be -4.8 MPa. However, one thing many people don’t understand is that there is still liquid water in frozen soils.

Where is the Liquid Water in a Frozen Soil?

Some liquid water will always be associated with soil surfaces because water, as a polar molecule, is attracted by opposite surface charges. Ice is a collection of water molecules that have slowed enough that they are arranged in a crystal-like structure. When ice arranges in that structure, it will attract and use all those water molecules that are available but will have difficulty stealing away water bound to soil surfaces. That water will remain liquid. As soil temperature drops, water layers closer and closer to soil particle surfaces will slow and join the ice structure.

Why Worry about Frozen Water Potential?

Previously, we’ve discussed the importance of water potential in determining the availability of water for plant growth. But below freezing, plants are either dormant or expired, so why measure frozen water potential?

There are a couple of reasons frozen soil water potential may be interesting to scientists. Liquid water in frozen soil still has the possibility to move. So, knowing soil temperature will allow models to predict water flow.  

Even more interesting is what could be done with a temperature sensor and a measurement of water content using dielectric permittivity. As we mentioned earlier, ice essentially disappears to a dielectric measurement.  Thus, a dielectric sensor water content measurement should provide the amount of liquid water in the soil. Using the temperature sensor to infer water potential (assuming the soil begins wet enough that its pre-frozen state has not reduced WP significantly), we can combine the WP and VWC measurements over a range of temperatures to generate an in situ moisture release curve. This idea was developed into a prototype instrument that appeared to have promise as a new laboratory technique to obtain moisture release curves.

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy

Oct 9

31 Comments

Water Content helps Turf Growers find Water/Nutrient Balance

Many athletes don’t like artificial turf. They say it’s hot, uncomfortable to run on, causes burns when you slide or fall on it, and changes the way a ball moves.  Professional women’s soccer players even started a lawsuit over FIFA’s decision to use artificial turf in the 2015 Women’s World Cup.

Soccer players running after the soccer ball on a green field

Soccer players on natural turf.

Some universities—including Brigham Young University—have responded to athlete concerns by using natural turf fields for practice and in their stadiums. But the challenge is to develop plants and management practices for natural turf that help it stand up to frequent use and allow it to perform well even during the difficult fall months. It’s a perfect research opportunity.

BYU turf professor and manager of BYU sports turf, Bryan Hopkins and his colleagues in the Plant and Wildlife Department, have been able to set up a new state-of-the-art facility to study plants and soil in both greenhouse and natural conditions. The facility includes a large section of residential and stadium turfgrass.  

Before Soil Sensors

Initially, BYU maintained the turf farm grass on a standard, timer-based irrigation control system, but over time they realized that understanding the performance of their turf relative to moisture content and nutrient load is crucial. Last year during Memorial Day weekend their turf farm irrigation system stopped working when no one was around to notice.  During those four days temperatures rose to 40 C (100 F), and the grass in the field slipped into dormancy due to heat stress. In response, Dr. Hopkins began imagining a system of soil moisture sensors to constantly monitor the performance of the turf grass.  He wanted not only to make sure the turf never died but also to really understand the elements of stress so they could do a better job growing healthy turf.

Sensors Give a Clear Picture

Soon afterward, a team of scientists, including fellow professor Dr. Neil Hansen, installed volumetric water content (VWC) and matric potential sensors at two different sites: one in the sports turf and one in a residential turf plot.  Each plot had two installations of sensors at 6 cm and 15 cm, along with VWC only at 25 cm, to measure water moving beyond the root zone. Combining these measurements, they could clearly see when the grass was reaching stress conditions and how quickly the turf went from the beginning of stress (in terms of water content and time) to permanent wilting point. In addition, ancillary measurements of temperature and electrical conductivity provide an opportunity for modeling surface and root zone temperature as well as fertilizer concentration dynamics.

Researcher digging a dirt canal and installing sensors

Installing water content sensors at the BYU turf farm.

Errors Revealed

What the researchers learned was that they were using too much water. Dr. Colin Campbell, a METER research scientist who worked with BYU on sensor installation, comments, “We found in the first year that the plants never got stressed at all. So this year, the researchers allowed the water potential (WP) at 6 cm to drop into the stress range (~ -500 kPa) while observing WP at 15 cm (-50 kPa to -60 kPa). We hope this approach will reduce irrigation inputs while creating some stress in the grass in order to push the roots deeper.”

What’s happening with the water?

Dr. Campbell’s favorite part of the sensor data was the detailed picture it gave of what was happening with the water in the sandy soil (Figure 1). He says, “Most people believe that they have an intuitive feel for water availability in soil.  If we were only using water content sensors, seeing a typical value of 20% would lead us to believe we were comfortably in the middle of the plant available range (A).  But in this study, using our colocated soil water content and soil water potential sensors, the data showed readings over 15% VWC were too wet to affect the WP (B). However, once WP visibly changed, it quickly moved toward critical stress levels (C, -1500 kPa is permanent wilting point); it only took two days for the water potential to change from -8 kPa to -1000 kPa.  A subsequent dry period (D) shows similar behavior, but this time the 15 cm WP drops to near -1000 kPa.”

Water potential changes diagram

Figure 1

The plant stress levels were reached surprisingly quickly in this soil because its sand composition has a lot of large pores and not very many small ones (Figure 2). Campbell explains, “The large pores store water that is not held tightly due to low surface area, so the water is freely available. But at around 10% VWC all the water from the large pores is used up. As the soil dries beyond that, the water is held tightly in small pores and becomes increasingly unavailable. This is clear in the moisture release curve.  We see almost no change in water potential as the soil dried to 16% VWC, but from 10% down to 7%, the water potential reached permanent wilting point, and it happened in just over a day.”

VWC and Water potential sensors diagram

Figure 2

What the Future Holds:

The researchers wanted to make sure that if they went down to certain stress levels, they wouldn’t cause harm to the plants, so this year, they installed a weather station to monitor evapotranspiration and calculate irrigation application rates.  They also began measuring spectral reflectance to monitor changes in leaf area (NDVI) and photosynthesis (PRI).  This will enable them to see the impact on the plants as the turf is drying down.  “In the future,” says Campbell, “we hope that both commercial and residential turf growers will be able to more effectively control their irrigation and nutrients based on what we find in this study.”

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy

Oct 2

Soil Moisture and Temperature Sensors Aid Landmine Detection

Anti-personnel landmines are one of the most dangerous environmental hazards worldwide. Each year thousands of people are injured by landmines buried in eighty different countries.  Ben Wallen, Ph.D. candidate and active military officer at the Colorado School of Mines, is using soil moisture and temperature sensors to model, simulate, and predict how environmental conditions affect landmine detection performance.

Researcher and an army graduate student standing next to "The U.S Army Corps of Engineers, Engineer Research and Development Center" sign

Landmine research conducted at the Engineer Research and Development Center (ERDC) by LTC Benjamin Wallen, a graduate student at Colorado School of Mines, and Stacy Howington, a senior research engineer at ERDC.

Landmine Detection

Anti-personnel landmines are difficult to detect. They are small and often contain very little metal. It is difficult to differentiate between a landmine and, for example, a rock.

Success depends on many factors, including the landmine’s physical composition and how long it’s been in the ground. The numerical and analytical models used to find the mines rely on detailed data about conditions in the subsurface.  Wallen and his Ph.D. advisor, Dr. Kate Smits, realized that changing environmental conditions—particularly changes in soil moisture content—were commonly overlooked in developing these models. By gaining a greater understanding of these dynamic environmental conditions, Wallen thought he could better calibrate the numerical models used in detection technologies such as ground penetrating radar.

Researcher and army engineer student working on an installation site

Installing METER sensors at landmine detection field site at the Engineer Research and Development Center (ERDC) by LTC Benjamin Wallen and Matthew Geheran, a student engineer at ERDC.

Comparisons

The goal of Wallen’s research was to improve understanding of the complex flow processes of water, water vapor, and air in the shallow subsurface.  He installed soil moisture and temperature sensors in a field site in order to understand how landmines buried at different depths affect spatial patterns of soil moisture.  He compared holes with mines at a shallow depth (2.5 cm) to more deeply buried mines (10 cm).  He also measured the environmental response to shallow empty holes roughly the size that you’d dig for the placement of a mine.  He realized if there was an identifiable response between a disturbed hole with nothing in it and a hole with a mine buried, researchers would be able to do experiments with different soils in a lab without needing a buried landmine in order to investigate the environmental response associated with a buried landmine.

Results

Wallen was able to see differences in the “with mine” and “without mine” treatments.  He says, “The soil moisture in the disturbed soil 2.5 cm below the surface with no landmine inserted matched very well to a shallow-buried mine.  The only time it really deviated was when there was a saturation event. At that point, there was a break from that relationship, but then, in 36 hours, the soil moisture returned to matching very closely between the disturbed soil hole and the shallow-buried mine.”  Wallen says there was also a relationship in the case of the more deeply buried mine. He adds, “For a deeply buried mine, both the soil moisture and temperature in the disturbed soil 2.5 cm below the surface had a strong correlation with the response to the dug, disturbed hole.”

Shallow Buried Mine- Soil Moisture as a Function of Depth diagram

Disturbed and Undisturbed Soil- Soil Moisture as a Function of Depth Diagram

An Array of Sensors is Crucial

Ben says it was important to his study to use a suite of measurement tools that complimented each other.  In addition to soil moisture and temperature sensors, he used an IR camera to detect surface temperature differences prior to the saturation event, during saturation event, and then afterward, helping identify the different scenarios of shallow-buried mines, deep buried mines, and the disturbed soil. He comments, “There are numerous global climate models that may be used to predict evaporation from energy balances in order to understand what is occurring. By combining the sensors in this minefield detection scenario, we were able to really understand what was going on at different depths with soil moisture and temperature, and that enabled us to better understand how the system responds.”

The Next Step

Now that Wallen has done a soil characterization of the site, he wants to incorporate the data into a 3D model to ensure that the model accurately represents the actual physical conditions he’s observed. The next step is modeling under different climatic conditions: seeing what the environmental response is for various mine scenarios in a different soil environment.

Making the World a Safer Place

The goal, according to Wallen, is to provide pertinent information that will improve landmine detection technologies. Understanding how temperature contrast impacts remote sensing technology and understanding how the soil moisture signature impacts ground penetrating radar.  Ben says, “Ideally, this information takes us one step farther in being able to identify potential locations for landmines, but there is a long way to go. This is just one piece of the pie, but every step forward moves us toward the goal of making the world a little bit safer for everyone.”

Acknowledgments:

This research was made possible through sensors provided by Decagon (now METER), funding from the Society of American Military Engineers Denver Metro Post, field site access from the Waterways Experimentation Station (WES), and assistance with equipment and research support from scientists and engineers at the Engineer Research and Development Center (ERDC) in Vicksburg, MS. Their support and knowledge based upon over a decade of research exploring disturbed soil for threat detection and environmental effects on sensor performance was essential to enable quality research at their site.

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy

Sep 19

Assessing Erosion Risk after Forest Fires

As forest fires throughout the Northwest die down, one scientist’s work is just beginning.  An article from our archives details the important research that takes place in the aftermath of the flames:

Forest on fire with sun shining through the smoke

In 2015, over eight million acres of forest burned in the United States. Major fires burned in five northwestern states: Washington, Idaho, Montana, Oregon, and California.

Flagstaff, Arizona is typically a dry place. But in August 2010, churning rivers flowed down roadways and around—and through—homes in the Flagstaff area. The floods were caused by a fire—the 15,000 acre Shultz fire that raged around Flagstaff from April to July, 2010.

One might not ordinarily think of a fire causing a flood, but to Forest Service research engineer Dr. Peter Robichaud, the setup is classic. “After a fire, you’ve changed the hydrology of the hillside,” he says. “Normally in an unburned area, rain gets soaked up by forest floor material on the ground and then it soaks into the soil. After a fire goes through, there’s no forest floor material to soak up the water and the soil may become water repellent due to heat from the fire.”

Reduced infiltration means increased runoff and erosion. As Robichaud explains, “If you have a steep slope and high velocities, along with very erodible soil, things converge rather quickly and you can generate debris flows and mudslides.  It’s not just a 100% increase. It’s orders of magnitude increase.”

Burned trees standing in a swampy area covered in water

After a fire, soil commonly becomes hydrophobic, just one factor in increased runoff.

One of Robichaud’s research interests is in designing a model for post-fire erosion. The model helps land managers and assessment teams in the field to evaluate the risks such erosion might pose. “It lets them see what might be affected if they have an erosion event,” he says.

“Is it going to affect the municipal water supply, affect a road crossing, an interstate highway, a school that happens to be at the mouth of a canyon? Once they can estimate the amount of erosion that might occur, they can use the model to help pick treatments to reduce the risk.”

Often practitioners will use the model to establish an early warning system to areas that will be affected.

Along with developing the model, Robichaud has also looked for ways to help postfire assessment teams gauge the water repellency of the soil after a fire. Historically, soil in a burned area was evaluated using the water drop penetration time test, or WDPT. Team members would place a drop of water on the surface of the soil and time how long it took to be absorbed. This seventies-era test was easy to do in the field, but Robichaud wanted something more representative.

Trees and a street covered in a pool of water

One of Robichaud’s research interests is in designing a model for post-fire erosion to help land managers and assessment teams in the field evaluate the risks such erosion might pose.

“I’ve always felt we could do a better job of characterizing the changes in soil condition,” he says. “[The WDPT] doesn’t really represent the physical process of the water infiltrating, because you put a single drop of water on the surface… The ideal method is a rainfall simulator, but it’s not practical in the field. [You] can’t expect every assessment team after a fire to set up a rainfall simulator for a couple of weeks.”

As he looked for alternatives, Robichaud started using a Mini Disk Infiltrometer. Practitioners all over the world use infiltration measurements along with Robichaud’s model of post-fire erosion to assess the impacts of a fire, predict erosion, and make plans to manage and reduce the associated risks. Robichaud’s online Erosion Risk Management Tool allows researchers and assessment teams alike to use scientifically solid analysis. He’s currently involved in refining and validating the model, improving assessment techniques, using remote sensing technology to perform assessments, and looking at alternative post-fire treatment options to reduce erosion risk, among other things.

To see what Dr. Robichaud’s been up to recently, read his 2014 paper, The temporal evolution of wildfire ash and implications for post-fire infiltration, published in the International Journal of Wildland Fire.   Find out more about Robichaud’s research, methods for use of the Mini Disk Infiltrometer for changes in infiltration characteristics after fire, or access the Erosion Risk Management Tool, by visiting the Moscow Forest Sciences Laboratory website.

Learn more about wildfire and soil moisture

See how soil moisture information could improve assessments of wildfire probabilities and fuel conditions, resulting in better fire danger ratings here.

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy

Sep 11

Scientists and Greenhouse Growers Collaborate to Help the Environment

Bodies of water across the world face extreme pressure from non-point source pollution.  It’s easy to get overwhelmed by the sheer enormity of this problem, but it didn’t daunt Dr. John Lea-Cox, Research and Extension Specialist for horticulture at University of Maryland.  Dr. Lea-Cox was acutely aware that agriculturally applied fertilizers threatened serious harm to the Chesapeake Bay area near his home. Using an early version of METER’s water content sensors, he began to put together a system that could monitor water status in nursery operations. The effort was based on the work of Dr. Andrew Ristvey (now a colleague at Maryland) who showed water savings of more than 50% during his PhD work using TDR sensors in pots growing ornamental plants.  Dr. Lea-Cox and his colleagues wanted to ultimately develop a network of soil moisture and environmental sensors that would help greenhouse and nursery growers know when to turn on and off their water. Their goal was to reduce nutrient and water use through more efficient application.

Close up of a yellow flower with red tipped petals

How did Dr. John Lea-Cox, Research and Extension Specialist for horticulture at University of Maryland, convince nursery growers to reduce water and fertilizer use?

Convincing Growers

One hurdle facing Dr.Lea-Cox was that water savings didn’t resonate with all growers.  But he soon realized that better irrigation control influenced things growers did care about: higher quality crops, lower mortality rate, and less spending on pesticides.  Dr. Lea-Cox discovered that when he showed growers their moisture sensor data, they were hooked. One snapdragon grower, who found that he could use the sensors to produce a more lucrative A grade crop, said he would not like to go back to the days before sensors. “My gosh, it would be like going back ten years. It would be like trying to measure the temperature in a room without a thermometer. We are totally dependent on them.”

Pink orchids growing in a nursery super green nursery

Orchids grown in a nursery.

Finding Collaborators

Dr. Lea-Cox was not only good at convincing growers, but scientific collaborators as well.  Building on this team’s initial findings, he organized a project to develop water retention curves to tie the amount of water in pots to what was actually available to the plant for several different mixes of potting soil. He realized that moisture measurements were practically useless to growers without a mechanism for viewing them all in one place, so he began to look for collaborators who could build an integrated, wireless system to get root zone information to the nursery grower’s computer and allow them to set irrigation limits and automate their systems based on soil and weather data.  

The resulting collaboration was a group of diverse scientists and commercial growers who could study root behavior, plant-environmental interactions, the performance of the plants, and individual grower interaction with the system.  After a few years of testing, the group received $5M in funding from the Specialty Crops Research Initiative (SCRI) Program over five years to improve horticulture for ornamental plants grown in the U.S.

Lauren Crawford, METER’s soils product manager, says that the resulting collaboration was unique. “It was amazing that an instrumentation company, a research group, and commercial growers were able to work so well together. It was because of the trust we had for each other. We were very transparent about what we were doing, even when we knew that transparency would be difficult. The result was that we were able to make tremendous progress in both science and technology.”

Watch two virtual seminars highlighting SCRI research given by scientists Marc Van Iersel and John Lea-Cox.

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy

Aug 28

2 Comments

Low Impact Design: Sensors Validate California Groundwater Resource Management

Michelle Newcomer, a PhD candidate at UC Berkeley, (previously at San Francisco State University), recently published research using rain gauges, soil moisture, and water potential sensors to determine if low impact design (LID) structures such as rain gardens and infiltration trenches are an effective means of infiltrating and storing rainwater in dry climates instead of letting it run off into the ocean.

Body of water with rain droplets hitting the surface

Can Low Impact Design Structures store rainwater?

Low Impact Design Structures

Global groundwater resources in urban, coastal environments are highly vulnerable to increased human pressures and climate variability. Impervious surfaces, such as buildings, roads, and parking lots prevent infiltration, reduce recharge to underlying aquifers, and increase contaminants in surface runoff that often overflow sewage systems. To mitigate these effects, cities worldwide are adopting low impact design (LID) approaches to direct runoff into natural vegetated systems such as rain gardens that reduce, filter, and slow stormwater runoff. LID hypothetically increases infiltration and recharge rates to aquifers.

Three pictures the first depicts an aerial view of an infiltration trench, the second depicts an infiltration trench site, and the third depicts a irrigated green lawn

Infiltration and Recharge

Michelle and the team at San Francisco State University, advised by Dr. Jason Gurdak, realized that the effects of LID on recharge rates and quality were unknown, particularly during intense precipitation events for cities along the Pacific coast in response to inter-annual variability of the El Niño Southern Oscillation (ENSO). Using water potential and water content sensors she was able to quantify the current and projected rates of infiltration and recharge to the California Coastal Westside Basin aquifer system. The team compared a LID infiltration trench surrounded by a rain garden with a traditional turf-lawn setting in San Francisco.  She says, “Cities like San Francisco are implementing these LID structures, and we wanted to test the quantity of water that was going through them.  We were interested specifically in different climate scenarios, like El Niño versus La Niña, because rain events are much more intense during El Niño years and could cause flash flooding or surface pollutant overflow problems.”

Infiltration trench site diagram

Sensors Tell the Story

The research team looked at the differences in the quantity of water that LID structures could allow to pass through.  Michelle says. ”The sensors yielded data proving LID areas were effective at capturing the water, infiltrating it more slowly, and essentially storing it in the aquifer.”  The team tested how a low-impact development-style infiltration trench compared to an irrigated lawn and found that the recharge efficiency of the infiltration trench, at 58% to 79%, was much higher than that of the lawn, at 8% to 33%.

Daily time series of precipitation and volumetric water content

Rain Gauges Yield Surprises

Though it wasn’t part of the researchers’ original plan, they used rain gauges to measure precipitation, which yielded some surprising data.  Michelle comments, “We were just going to use the San Francisco database, but it became necessary to use the rain gauges because of all the fog.  The fog brought a lot of precipitation with it that didn’t come in the form of raindrops.  As it condensed on the leaves, it provided a substantial portion of the water in the budget, and that was surprising to me.  The rain gauge captured the condensate on the funnel of the instrument, so we were able to see that a certain quantity of water was coming in that is typically neglected in many studies.”

Future El Niño Precipitation

Michelle also found some really interesting results regarding El Niño and La Niña.  She says, “I did a historical analysis to establish baselines for frequency, intensity, and duration of precipitation events during El Niño and La Niña years.  I then ran projected climate data through a Hydrus-2D model, and the models showed that with future El Niño intensities, recharge rates were effectively higher for a given precipitation event. During these events, in typical urban settings, water runs off so fast that only these rain gardens and trenches would be able to capture the rain that would otherwise be lost to the ocean. This contrasts with a La Niña climate scenario where there’s typically less rain that is more diffuse. Most of that rain may eventually be lost to evaporation during dry years.  So using sensors and 2D modeling we have validated the hypothesis that LID structures provide a service for storing water, particularly during El Niño years where there are more intense rainstorms.”

Michelle’s research received some press online and also was featured in the AGU EOS Editor’s spotlight.   Her results are published in the journal Water Resources Research.

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy

Aug 22

Author Interview: Soil Physics with Python

The new book Soil Physics with Python: Transport in the Soil-Plant-Atmosphere System written by Dr. Marco Bitteli, Dr. Gaylon S. Campbell, and Dr. Fausto Tomei presents concepts and problems in soil physics as well as solutions using original computer programs.

Picture of the cover of the book "Soil Physics with Python" by Marco Bittelli, Gaylon S. Campbell, and Fausto Tomei

Soil Physics with Python

In contrast to the majority of the literature on soil physics, this text focuses on solving, not deriving, differential equations for transport. Numerical methods convert differential equations into algebraic equations, which can be solved using conventional methods of linear algebra.  Here, Dr. Campbell interviews about this update to his classic book Soil Physics with BASIC.

Why did you write the first book, Soil Physics with BASIC?

Soil physics classes were always frustrating for me because you would spend time writing fancy equations on the chalkboard, and in the end, you couldn’t do anything with them.  You couldn’t solve any of the problems because, even though they involved difficult mathematics, the math was still so simplified that it didn’t apply to anything that went on in nature.

When I taught my first graduate soil physics class, I determined that we were going to be able to do something by the time we finished.  Luckily, in the mid-1970s, personal computers were being developed, and I realized this was the answer to my problem.  Numerical methods could solve any problem with any geometry in it.  It wasn’t limited to problems that fit the assumptions needed to derive a complex differential equation.  I could write computer programs that simplified the mathematics for the students and teach them how to solve those problems using numerical methods.  By the end of the semester, my students would have a set of tools that they could use to solve problems in the real world.  

Did this book come from class notes or some other source?  

I wrote two textbooks and they both came the same way.  When I first started teaching, I had a textbook that was inadequate, so I began writing notes of my own and handing them out to the students.   After two years, I turned these notes into An Introduction to Environmental Biophysics.  Soil Physics with BASIC came about by the same process, but I enlisted the help of my daughter, Julia, to type it up. It was in the early days of word processing so entering equations was quite difficult.  It all went well for her until chapter eight, which was a nightmare of greek symbols. After she finished slogging for days through the material, we somehow lost the chapter.  She retyped it, and we lost it again, making her type it three times!  We didn’t have spreadsheets then either, so the figures were all hand-drawn by my daughter, Karine.

Red soil in the desert with trees and brush around

Marco [Bitteli] has added two and three-dimensional flow problems, so you can model whole landscapes and water behavior in an entire terrain.

What does Soil Physics with Python add to the conversation?

First, it updates the programming language.  BASIC was a language invented at Dartmouth and intended to be a simple teaching language.  It was never supposed to be a scientific computer language.  Python (13:26.) is a newer language, and there are many open source programs for it, making it a better language to use for science.

Secondly, the old book had one-dimensional flow problems in it for the most part, but Marco [Bitteli] has added two and three-dimensional flow problems, so you can model whole landscapes and water behavior in an entire terrain.

In addition, Dr. Bitteli describes the process and analysis of soil treated as fractals as well as soil image analysis.  There are a lot of extensions and updates that weren’t in the original book.  

Will it be accessible across all disciplines?

To some extent, different disciplines speak different languages.  A soil physicist talks about water potential, and a geotechnical engineer talks about soil suction. Thus, there may be some translation of discipline-specific terms, but it’s intended to be a book that people in the plant sciences can use along with people in the soil sciences.

Dr. Marco Bitteli earned his PhD at Washington State University and was Dr. Campbell’s former student.  This book is a product of their continued collaboration. Dr. BBitteli is now a professor at University of Bologna, the oldest university in operation in the world.  Soil Physics with Python  is available at Amazon.com.

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy

Aug 7

New Medium Scale Soil Moisture Measurement Technique

Between dielectric soil moisture sensors with a volume of influence measured in liters and remote sensing systems which measure soil moisture on the scale of kilometers, there is a gap—a gap Dr. Larry Murdoch of Clemson University has been working to fill. In this post, read about the DELTA (Displacement Extensometer for Lysimetric Terrain Analysis), an instrument that measures water content measurements over an area with a 25 m radius.

Close up picture of cracked and dried soil

Dr. Murdoch became interested in how much water content was in the vadose zone (the unsaturated soil above the water table). He wondered if he could use a strain measuring technique to quantify it.

A New Idea:

Dr. Murdoch was a graduate student in structural geology and geomechanics in the mid-1980s, working on the mechanics of hydraulic fractures in soil.  He developed techniques for environmental “fracking” to clean up contaminated soil, long before the recent applications by the oil industry that have caused fracking to become a household word.  Fracking causes movements in soil, and Dr. Murdoch developed methods for measuring those movements in order to monitor fracture displacement. This led to work on sensitive borehole extensometers that could measure small strains in rock during well testing.

In the course of his hydrology work, Dr. Murdoch became interested in how much water content was in the vadose zone (the unsaturated soil above the water table). He wondered if he could use the strain measuring technique to quantify it.  He decided to bore a hole into the vadose zone and insert a simplified extensometer device that could measure the strain as the soil expands and contracts.  This would allow him to gauge the weight change of the overburden.  Then, because other mass changes are relatively minor compared to the water in the soil, that weight change would enable him to determine water content.

Since soil compresses more than bedrock, Dr. Murdoch developed a method where he inserted two anchors and cylinders that are pressed up against the soil borehole.  In the middle of these cylinders is a fiberglass rod held tight by the bottom anchor which is able to move inside the top anchor.  The anchors move up and down from the stress on the soil, and this movement is transferred to the rod where it can be measured with a high-resolution displacement transducer.

Diagram of the Delta (Displacement Extensometer for Lysimetric Terrain Analysis)

Diagram of the DELTA (Displacement Extensometer for Lysimetric Terrain Analysis)

Dr. Murdoch’s device is so sensitive that when it is buried 6 m, it will register clear strain signals as his student walks over it. The weight of a person causes around 50 nanometers of displacement at the Clemson Field site, but the instrument itself can resolve displacement approaching 1 nanometer. And the diameter of measurement on the surface is about 4 times the depth.  So if you install the system at 7m, you’d be measuring about a 25 m diameter circle on top.

Like almost all other water content techniques, the challenge is removing all other confounding factors that affect the measurement. It has been said that all sensors are temperature sensors first.  Not surprisingly, one thing that causes errors in the system is temperature, though Dr. Murdoch’s team has dealt with that by getting the system deep in the soil and putting the electronics near it so the temperature change is small.  Barometric pressure also produces cyclical loading of soil mass and requires correction over a range of periods. And, since the calculation of water content requires an estimate of the soil elasticity, changes in soil moisture also may affect the measurement. Considerable work has been done and significant progress has been made in dealing with these and other issues with the extensometer approach.

picture of a field with a barn in the distance and the ski orange and grey

An advantage of the system is its ability to be buried. In order to plow, for example, all you have to do is pull the sensor up, take off the top plastic casing, and cap it, and the grower can drive a plow over the top.

Strengths:

The amazing thing is that Dr. Murdoch’s system can resolve less than a millimeter of rain water falling on the soil surface, and it can match trends over time. In addition, you can easily calibrate the system by getting your 190-pound student to walk over the top of it and then checking that the compressibility of the soil matches that weight.

Another advantage of the system is its ability to be buried.  In order to plow, for example, all you have to do is pull the sensor up, take off the top plastic casing, and cap it, and the grower can drive a plow over the top. Finding the installation can be challenging, so it must be located by precision GPS or survey equipment prior to burial. But, if done correctly, the site can be monitored for long periods of time.

Though not yet a final technology, the Delta extensometer did correlate well with point measurements of water content and shows a lot of promise. The instrument was developed with funding from the National Science Foundation. Colby Thrash, a grad student at Clemson, has done much of the recent work. Dr. Murdoch’s team will publish a paper describing the technique soon in Water Resources Research.

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy

Jul 31

34 Comments

Water Potential Versus Water Content

Dr. Colin Campbell, soil physicist, shares why he thinks measuring soil water potential can be more useful than measuring soil water content.

A horsetail plant showing possible signs of guttation where the water potential in the soil overnight is high enough to force water out of the stomates in the leaves.

A horsetail plant showing possible signs of guttation where the water potential in the soil overnight is high enough to force water out of the stomates in the leaves.

I know an ecologist who installed an extensive soil water content (VWC) sensor network to study the effect of slope orientation on plant available water.  He collected good VWC data, but ultimately he was frustrated because he couldn’t tell how much of the water was available to plants.

He’s not alone in his frustration. Accurate, inexpensive soil moisture sensors have made soil VWC a justifiably popular measurement, but as many people have discovered, a good hammer doesn’t make every soil water problem a nail. I like to compare water potential to temperature because both are considered “intensive” variables that define the intensity of something.

People often try to quantify their own environment, because those measurements define comfort and happiness.  Long ago, they discovered they could make an enclosed glass tube, put mercury inside, and infer this intensive variable called temperature from the changes in the mercury’s volume. This was an obvious way to define the comfort level of a human being.

Thermometer laying on top of wood

People discovered they could make an enclosed glass tube, put mercury inside, and infer an intensive variable called temperature.

They could have measured the heat content of their surroundings.  But they would have discovered that while heat content would be higher in a larger room and lower in a smaller room, you would feel the same comfort level in both rooms.  The temperature measurement helps you know whether or not you’d be comfortable without any other variables entering into the equation.

Similar to heat content, water content is an amount. It’s an extensive variable.  It changes with size and situation. Consider the following paradoxes:

  • A soil with fairly low volumetric water content can have plenty of plant-available water and a soil with high water content can have almost none.
  • Gravity pulls water down through the profile, but water moves up into the soil from a water table.
  • Two adjacent patches of soil at equilibrium can have significantly different water content.

In these and many other cases, water content data can be confusing because they don’t predict how water moves.  Water potential measures the energy state of water and thus explains realities of water movement that otherwise defy intuition. Like temperature, water potential defines the comfort level of a plant.   Similar to the room size analogy for temperature, if we know the water potential, we can know whether plants will grow well or be stressed in any environment.

sand with plants poking out and a blue sky in the background

Soil, clay, sand, potting soil, and other media, all hold water differently.

Plants don’t understand the concept of a content in terms of “comfort” because soil, clay, sand, potting soil, and other media, all hold water differently.  Imagine a sand with 30% water content. Due to its low surface area, the sand will be too wet for optimal plant growth, threatening a lack of aeration to the roots, and flirting with saturation.  Now consider a fine textured clay at that same 30% water content. The clay may appear only moist and be well below optimum “comfort” for a plant due to the surface of the clay binding the water and making it less available to the plant.

Water potential measurements clearly indicate plant available water, and, unlike water content, there is an easy reference scale. We know that plant optimal runs from about -2-5 kPa which is on the very wet side, to about -100 kPa, at the drier end of optimal.  Below that plants will be in deficit, and past -1000 kPa they start to suffer.  Depending on the plant, water potentials below -1000 to -2000 kPa cause permanent wilting.

So, why would we want to measure water potential? Water content can only tell you how much water you have.  If you want to know how fast water can move, you need to measure hydraulic conductivity.  If you want to know whether water will move and where it’s going to go, you need water potential.

Learn more

Soil moisture is more than just knowing the amount of water in soil. Learn basic principles you need to know before deciding how to measure it. In this 20-minute webinar, discover:

  • Water content: what it is, how it’s measured, and why you need it
  • Water potential: what it is, how it’s different from water content, and why you need it
  • Whether you should measure water content, water potential, or both
  • Which sensors measure each type of parameter

Many questions about water availability and movement are best answered by measuring water potential.  To find out more, watch any of the virtual seminars below, or visit our new water potential website.

Download the “Researcher’s complete guide to water potential”—>

Water Potential 101: Making Use of an Important Tool

Water Potential 201:  Choosing the Right Instrument

Water Potential 301: How to Push Your Instruments Past their Specifications

Water Potential 401: Advances in Field Water Potential

Find out when you should measure both water potential and water content.

Take our Soil Moisture Master Class

Six short videos teach you everything you need to know about soil water content and soil water potential—and why you should measure them together.  Plus, master the basics of soil hydraulic conductivity.

Watch it now—>

Download the “Researcher’s complete guide to soil moisture”—>

LinkedInMessengerRedditThreadsCopy

Jul 11

Great Science Reads: What our Scientists are Reading

We asked our scientists to share the great science reads they’ve perused recently.  Here’s what they’ve been reading:

Open book with Highlighter and Glasses on top of it

Letters to a Young Scientist by E.O. Wilson

Edward Wilson's book "Letters To A Young Scientist"

Steve Garrity: E.O. Wilson is a leader in the science of biology. This book is a simple read. What I like most about it is that it very effectively conveys Dr. Wilson’s passion for science. His thoughts on what it takes to be a successful scientist resonated with me the most.  In describing what it takes to be a successful scientist, E.O. Wilson says that being a genius, having a high IQ, and possessing mathematical fluency are all not enough. Instead, he says that success comes from hard work and finding joy in the processes of discovery. Dr. Wilson gets specific and says that the real key to success is the ability to rapidly perform numerous experiments. “Disturb nature,” he says, “and see if she reveals a secret.” Often she doesn’t, but performing rapid, and often sloppy, experiments increases the odds of discovering something new.

Out of the Scientist’s Garden by Richard Stirzaker

Picture of the cover of "Out Of The Scientist's Garden- A Story Of Water And Food"

Lauren Crawford: “Richard Stirzaker is a scientist out of Australia committed to finding tools to make farming easier and more productive in third world countries.  I love how he talks about what happens when he uses water from his washing machine on his garden and the unanticipated effects: what does the detergent do to the fertilizers and the soil properties?  It’s a scientific view of how a garden works.”

Introduction to Water in California by David Carle

The cover of the book "Introduction To Water In California" by David Carle

Chris Lund: “This is a great introduction to California’s water resources, from where the water comes from to how it is used….particularly relevant today given California’s ongoing drought and the hard choices California faces as a result.”

The Drunkard’s Walk:  How Randomness Rules our Lives, by Leonard Mlodinow

A picture of the cover of the book "The Drunkard's Walk- How Randomness Rules Our Lives" by Leonard Mlodinow

Paolo Castiglione:  “The Drunkard’s Walk’s beginning quote perfectly reflects the author’s thesis: “In God we trust. All others bring data!”. I enjoyed the author’s discussion on how the past century was strongly influenced by ideologies, in contrast to the present one, where data seems to shape people’s actions and beliefs.”

Chapter 13 of An Introduction to Environmental Biophysics, by Gaylon Campbell

A picture of the cover of the book "An Introduction To Environmental Biophysics" by Gaylon S. Campbell and John M. Norman

Colin Campbell:  “Because of teaching Environmental Biophysics class, all my focus has been on reading An Introduction to Environmental Biophysics.  And, although I’ve read it too many times to count, I finally had a chance to study the human energy balance chapter (13) in depth, which was amazing.  The way humans interact with our environment is something we deal with at every moment of every day; often not giving it much thought. In this chapter, we are reminded of the people of Tierra del Fuego (Fuegians) who were able to survive in an environment where temperatures approached 0 C daily, wearing no more than a loincloth. Using the principles of environmental biophysics and the equations developed in the chapter, we concluded that the Fuegian metabolic rate had to continuously run near the maximum of a typical human today. The food requirements to maintain that metabolic rate would be somewhere between the equivalent of 17 and 30 hamburgers per day (their diet was high in seal fat).  You can read more about the Fuegians here.”

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

LinkedInMessengerRedditThreadsCopy
« Older Entries
Newer Entries »